Description
This Used John Deere 900 Series Cutting Platforms Operators Manual provides you with everything you need to operate and service John Deere 900 Series Cutting Platforms. Issue K9. Copyright 1989.
CONTENTS
Safety
Safety Signs
Attaching and Detaching
Attaching Platform to 9400, 9500 and 9600 Combine
Detaching Platform From 9400, 9500 and 9600 Combines
Attaching Platform to 6620, 7720 and 8820 Combine (600001 -)
Detaching Platform From 6620, 7720 and 8820 Combine (600001 -)
Attaching Platform to Sidehill 6620 Combine (610001-)
Detaching Platform From Sidehill 6620 Combine (610001-)
Transporting
Operating the Platform
Checking Platform Speeds
Combining Soybeans-Flex Platforms
Combining Oats, Maize and Wheat In Dry Ground Conditions (All Platforms)
Combining Oats, Maize and Wheat In Damp or Wet Ground Conditions (All Platforms)
Combining Oats, Maize and Wheat In Short Thin Crops (All Platforms)
Combining Rice and Barley (All Platforms)
Setting Reel
Setting Reel Safety Stops
Manual Adjusting of Pickup Reel-Fore/Aft
Adjusting Divider Points for Reel Finger Clearance
Adjusting Pickup Finger Pitch
Reel End Shields
Manual Adjusting of Slat Reel-Fore/Aft
Hydraulic Adjustment of Reel-Fore/Aft
Reference Point Indicator (Optional Reel Fore/Aft)
Adjusting Width Between Reel Arms
Adjusting Reel Lowering Speeds ( 6620, 7720 and 8820 Combines)
Adjusting Reel Height and Leveling Reel
Checking Reel Height
Rephasing Reel Cylinders
Bleeding the System
Cutterbar/Skid Plate Tilt Adjustment (All Platforms)
Cutterbar Position (Rigid Platform Only)
Adjusting Cutterbar Forward (Rigid Platforms Only)
Adjusting Cutterbar Rearward (Rigid Platforms Only)
Locking-Out Flex Cutterbar Platform
Removing Lock-Out Washers for Flex Cutterbar Operation
Adjusting Cutterbar Drive Case Support Spring (Flex Platforms Only)
Adjusting Stabilizer Spring Assembly (Flex Platforms Only)
Adjusting Auger Height on Right-Hand Side
Adjusting Auger Height on Left-Hand Side
Adjusting Stripper
Adjusting Auger Forward and Rearward
Adjusting Auger Chain
Floor Strippers (Attachment)
Auger Anti-Wrap Shields
Auger Flight Extensions
Adjusting Range Indicator (Flex Platforms Only)
Floating Divider Points
Removing Floating Divider Points for Standing Crops
Dial-A-Matic Header Height Control
Dial-A-Matic Electrical System (9400, 9500 and 9600 Combines)
Dial-A-Matic Electrical System (6620, 7720 and 8820 Combines)
Disconnecting Dial-A-Matic (9400, 9500 and 9600 Combines)
Disconnecting Dial-A-Matic (6620, 7720 and 8820 Combines)
Dial-A-Matic Hydraulic System (9400, 9500 and 9600 Combines)
Dial-A-Matic Hydraulic System (6620, 7720 and 8820 Combines)
Positioning Switch
Adjusting Housing
Adjusting Platform Drop Rate (9400, 9500 and 9600 Combines)
Adjusting Platform Drop Rate (6620, 7720 and 8820 Combines)
Adjusting Actuating Switch (6620, 7720 and 8820 Combines)
Dial-A-Speed (Optional)
Speed Ratio Sensor Adjustment
Soybean Looses
Lubricants
Lubrication and Maintenance
Troubleshooting
Service
Hydraulic Cylinder Safety Stop (9400, 9500 and 9600 Combines)
Hydraulic Cylinder Safety Stop (6620, 7720 and 8820 Combines)
Replacing Cutterbar Knife
Adjusting Knife
Setting Knife Register
Spare Knife Storage
Adjusting Hold-Down Clips
Adjusting Wearing Plates
Knife Section Service Kit
Replacing Knife Sections
Aligning Guards
Adjusting Non-Clog Cutterbar Guards (Attachment)
Attaching Lifting Guards
Replacing Cutterbar Drive Belt
Adjusting Fixed Idler Position
Cleaning Dirt From Under Flexible Seals
Adjusting Auger Slip Clutch
Auger Fingers
Storage
End of Season Service
Beginning of Season Service
Crime Prevention Tips
Specifications
